This hardware set will work with any base plate or 4-bolt tracked board on the market.  This included M8 or M6 base plates and tracks.  There is no more need for T-nuts or different sized bolts the Wizardhat will work on any.  Also, the way the bolt sticks up through the track on top makes it easy to line up with the base plate.

The complete Wizardhat kit comes with a 15mm ratchet wrench, 4 qty Wizardhat hardware sets, a set of 4 qty 30mm extra t-bolts, and a decal.  Choose from the standard length set at 35mm or the short version at 25mm.  The short 25mm version is for very low profile tracks like the FoilMount Carbon 3.0 or some of the F-One Wing boards.  For more options you can buy any length T-bolt you want from 25mm, 30mm, 35mm, and 40mm separately.

Be careful not to over- tightening with the wrench as you will have a lot more leverage than the screwdrivers you have been using. 

 

Extra brass T-nuts for your tracked hydrofoil sold each.  These are salt water approved and perfect for all track systems.  They are M8 standard metric threads which is the convention for most hydrofoil tracks.  These are sold per each.  

If you have a bulk order contact us at sales@foilmount.com

Measurements: 
15mm width
19mm length
8.5mm height
8.6mm width of center section with threads
3.95mm height from bottom of step

These M8 brass T-nuts are freshwater and salt water approved.  They are milled brass for superior strength and will fit any standard US track box.  The brass prevents corrosion in the connection system.  This 10 pack is a great way to keep extra T-nuts around.

Measurements:
15mm width
19mm length
8.5mm height
8.6mm width of center section with threads
3.95mm height from bottom of step

These are low profile replacement M8 Stainless Steel T-nuts for the any hydrofoil that uses the M8 T-nut, which just about all Tracked hydrofoils.  The low profile t nuts can be used in some foils that use M6 t-nuts as they are the same low profile.  These are low profile meaning they are thinner than stock brass T-nuts by about 2.2mm from top to bottom but STRONGER.  See the video below for some of the testing including breaking T-nuts in slow motion.  Sold each.

This is the dimensions of this part:

These are also available in M6 on a separate product listing. 

These are low profile replacement M8 Stainless Steel T-nuts for the any hydrofoil that uses the M8 T-nut, which just about all Tracked hydrofoils.  The low profile t nuts can be used in some foils that use M6 t-nuts as they are the same low profile.  These are low profile meaning they are thinner than stock brass T-nuts by about 2.2mm from top to bottom but STRONGER.  See the video below for some of the testing including breaking T-nuts in slow motion.  Sold in pack of 10qty.

This is the dimensions of this part:

These are also available in M6 on a separate product listing. 

These are Replacement M6 Stainless Steel T-nuts for the any hydrofoil that uses the M6 T-nut including Takuma, Naish and others  These are hard to get replacements that we now have in stock.  They are sold each so if you need a set of 4 make sure to buy 4 of them.  Watch the video below for our testing of the M8 version against the brass version. 

Here are the total dimensions of this part: 

Track width: 8.5mm
Total width: 14.9mm
Total length: 23.9mm
Total height: 6.20mm

These are extra stainless steel M8 bolts for your hydrofoil setup.

These are all countersunk flat head Stainless Metric Bolts in various sizes.  We can tell you what size you need for most foil setups.  The best way to do it is to measure the bolts you need from the ones that are already on your foil. Use the graphic below. 

These are extra stainless steel M8 bolts for your hydrofoil setup.

These are all Pan Head Stainless Metric Bolts in various sizes.  We can tell you what size you need for most foil setups.  The best way to do it is to measure the bolts you need from the ones that are already on your foil. Use the graphic below.